An Easy Song To Learn For Beginning Guitar Players


In this guitar lesson / guitar tutorial we teach you how to play Thinking Out Loud by Ed Sheeran on guitar. This lesson will start at the beginner guitar level, and walk through the guitar chords in an easy, simplified way with a few easier, alternative ways to play the chords and the rhythm. You will learn how to play this song without using a guitar capo or barre chords.
The original song is played by Ed Sheeran with a fingerstyle approach to playing the chords which creates an interesting sound and rhythmic feel (but can be challenging for the beginner guitar player) This lesson teaches how to play that style in the second half of the lesson (starts at 11:17). The first half of the lesson focuses on a simpler way to play the song using a guitar pick and is geared more to the beginner guitar player.
This lesson also teaches how to play easy chords as alternative versions of some of the more complicated chords like the Bmin chord which is a barre chord. You will also learn a simpler strumming pattern so that you can quickly start playing the song. As you become more comfortable in the chord progression and changing chords quickly, you can progress to the Ed Sheeran style of finger style guitar.

Introduction- 0:05
Verse Chords- 1:00
A Major Chord Substitute A2- 3:10
Pre Chorus- 6:35
B Minor Chord Cheater Version- 8:28
Chord Walk-Down- 10:19
Finger Style Playing- 11:17
Hammer On Riff #1- 14:29
Hammer On Riff #2- 15:44

For more beginner guitar lessons focusing on how to play guitar chords and guitar scales, music theory and technique visit our lesson channel

Studio 33 Guitar Lesson Channel https://www.youtube.com/channel/UCSef6897dNLTtC99y5G1T5w

 

Guitar Playing Lessons For Those Just Starting Out


Here’s a tutorial on how to play Just by Radiohead. I’m using a Vigier Excalibur Supra, and a Peavey Classic 50 amp.

Learning How To Play The Guitar

Starting Out With The Electric Guitar

Step by step instructions on how to make a solid body guitar on the CNC using parts from a cheap Epiphone Les Paul.

For this build I’m going to take an inexpensive Epiphone Les Paul and gut it for the electronics and the neck.

The first thing I’m going to do is sand off all the paint from the neck and modify the headstock.

Now I’ll mill up my lumber for the body. I’m using eight quarter ash that will need to be glued up for width.

After the glue dries I’ll plane it down to 1 5/8 inch thick. When CNCing wood this thick it needs to be rock solid secure so I’m going to screw my blank right to my waste board. I’ll cut out one pocket at a time starting with the neck. You’ll want to do some test cuts in scrap wood to be sure your neck fits in very snug.

Next I’ll move on to my pickup pockets and the cavity for the electronics.

And then finally carve the outer shape.

To save time I’m only carving about a quarter of the way through and then I’ll finish it up on the bandsaw and router table. Following the grooves left by the CNC I’ll rough cut the outer shape on the bandsaw. And then finish everything up with a flush trim bit installed in my router table.

Next I’ll round over the top and bottom face with a 1/4” round over bit.

Now I’ll mark where to remove the material for the arm contour.

I’m using an angle grinder and the Arbortech Turbo Plane blade.

I’ll then clean it up with a belt sander.

I’ll repeat the process for the belly cut on the back side.

For the neck I’m using, it requires it to be set at a slight angle so I’ll cut out a wedge on the bandsaw, sand it down and glue it in the neck pocket. I’m using a 3-ply pick guard material that has a black decorative core.

And the last thing I need to cut is the headstock laminate. I’ll etch my logo into the top to reveal the gold under layer. With some quick set epoxy I’ll glue and clamp the laminate on the headstock. Once it dries I’ll sand it flush and transfer the tuning peg holes.

Using some nails I’ll transfer the screw holes on the neck to the body by applying pressure and marking the indentations. And then drill them out over on the drill press and assemble the neck.

Next I’ll mark the lines where the bridge and tailpiece need to go. Distance from the nut to the bridge depends on the scale length and frets of your neck. I chose to buy a higher quality bridge than the one that was on the Ephiphone.

For the tailpiece i’ll keep it center aligned with the neck, drill the holes and pound in the threaded inserts.

For the bridge I’ll string up the high E and low E strings and use that as a guide to find the sweet spot. I then then visually see by wiggling it back and forth where I want the placement. Mark my holes with an ice pick, drill and pound in the treaded inserts.

And the final bit of work for the body is to drill a hole for the instrument cable jack. All the electronics will be attached to the underside of my pick guard so I’ll need to drill holes for the knobs and the pickup switch. The only modification I needed to do to the electronics was extend the length of one wire and this was easily done with a solder sleeve available in the Inventables store. Just slip the wires into the sleeve and use a heat gun. No soldering iron needed.

Last thing to do is attach everything to the pick guard, drill the pilot holes and screw it down.

Original Article: https://makesomething.tv/how-to-make-guitar/